| 當前位置：首頁->方案設計 |
|
| L6472全集成微步進馬達驅動方案 |
|
|
| 文章來源： 更新時間：2014/8/19 9:51:00 |
在線咨詢： |
| |
ST公司的L6472全集成微步進馬達驅動器,采用模擬混合信號技術,集成了低RDS(on) DMOS全橋和所有的功率開關以及精確的片上電流檢測電路,工作電壓8-45V,輸出峰值電流7.0A,高達1/16的微步進,非常適合驅動帶微步進的兩相雙極步進馬達.本文介紹了L6472主要特性,框圖,應用電路以及采用L6472和STM32的評估板EVAL6472H-DISC主要特性,電路圖,材料清單和PCB設計圖與元件布局圖.
The L6472 device, realized in analog mixed signal technology, is an advanced fully integrated solution suitable for driving two-phase bipolar stepper motors with microstepping. It integrates a dual low RDS(on) DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non dissipative current control and overcurrent protection. Thanks to a new current control, a 1/16 microstepping is achieved through an adaptive decay mode which outperforms traditional implementations. The digital control core can generate user defined motion profiles with acceleration, deceleration, speed or target position, easily programmed through a dedicated register set.
All application commands and data registers, including those used to set analog values (i.e. current control value, current protection trip point, deadtime, etc.) are sent through a standard 5-Mbit/s SPI.
A very rich set of protections (thermal, low bus voltage, overcurrent) makes the L6472 device“bullet proof”, as required by the most demanding motor control applications.
L6472主要特性:
Operating voltage: 8 - 45 V
7.0 A output peak current (3.0 A r.m.s.)
Low RDS(on) Power MOSFETs
Programmable speed profile
Programmable Power MOSFET slew rate
Up to 1/16 microstepping
Predictive current control with adaptive decay
Non dissipative current sensing
SPI interface
Low quiescent and standby currents
Programmable non dissipative overcurrent protection on all Power MOSFETs
Two levels of overtemperature protection
L6472應用:
Bipolar stepper motor
圖1. L6472框圖
圖2. L6472雙極步進馬達控制電路圖
采用L6472和STM32的評估板EVAL6472H-DISC
The EVAL6472H-DISC can be used together with the STM32™ firmware library V1.0 and constitutes a complete motor control evaluation and a development platform.It is a demonstration board for motor control applications in the range of 8 V to 45 V of DC bus voltage using the STM32F105RB microcontroller with an internal 128 kB Flash size and a 64 kB internal RAM and the L6472H fully integrated solution suitable for driving two-phase bipolar stepper motors up to 1/16 microstepping.
The L6472H device integrates a dual DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non-dissipative current control and overcurrent protection.
With dedicated hardware evaluation features, the EVAL6472H-DISC board is designed to help developers evaluate the device and develop their own applications.
評估板EVAL6472H-DISC主要特性:
DC voltage range from 8 V to 45 V
Maximum load phase current at 3 A r.m.s.
Footprint for external resonator or crystal
Control interface through trimmer - user keys and switch motor input
Control through LED indicators
Interface control by USB and debug outputs
Compatible with SPIN family evaluation tool
Autonomous board due to embedded firmware
Up to 1/16 microstepping
Optimized layout on 2-layer board - low cost and high thermal performance
評估板EVAL6472H-DISC目標應用:
The demonstration board is designed to fit all typical stepper motor applications - it is an
autonomous board due to embedded firmware.
圖3. 評估板EVAL6472H-DISC外形圖
圖4. 評估板EVAL6472H-DISC電路圖
圖5. 評估板EVAL6472H-DISC PCB元件布局圖:頂層
圖6. 評估板EVAL6472H-DISC PCB設計圖
評估板EVAL6472H-DISC 材料清單:
 |
| |
|
|
|
|
|
| |
|
| |
|
|
